GARLAND

Compatible with snap on hose connectors. Replacement Tap can be used as a standard Tap for filling watering cans or can be used with Snap on hose connectors. Suitable for most makes of water butt. When fitting the tap make sure the washer is on the outside and tighten the tap from the inside using the plastic nut. PACK INCLUDES: 1 x Water Butt Tap 1 x Washer 1 x Nut (25mm fitting)

Easily link 2 water butts together for greater water storage capacity. BEWARE Do not use an electric drill if the Butt contains water. Fitting Instructions: Before drilling make sure both butts are facing each other with the taps at the front. The water butts to be connected should be on a level surface and no more than 39cm apart. The water butts can be connected at the bottom, then the two water butts will fill at the same rate. If connected at the top the first butt will fill then run over into the second. Drill a 25mm hole approx. 25cm from the top or the bottom into opposite sides of the water butts to be connected. Join the water butts together with the supplied hose. Push the connector through the washer from the inside of each butt, then fit and tighten the nut outside to form a seal. KIT INCLUDES: 1 x 500mm Connector Hose 2 x 20mm Connectors 2 x Washers 2 x Nuts

Collect the water that falls on your house roof, shed or greenhouse automatically from your rain down pipe. Fits standard 68mm round or 65mm square plastic down pipes (not suitable for cast iron down pipes). BEWARE Do not use an electric drill if the Butt contains any water. Fitting Instructions: Take the lid off the water butt. If your water butt is not predrilled then you will need to drill a 25mm hole to fit the rain diverter. Drill a 25mm hole near the top of the water butt on the side closest to the down pipe (some water butts may have drill points indicated). Push connector through the washer from inside the butt, then fit and tighten the nut on the outside to form a seal. Position water butt with tap facing forward and adjust to down pipe. If using a stand place the butt on it. Mark the down pipe 10mm below the top of the butt. Mark again 30mm below this point, using a hacksaw. Cut out this section. Fit rain diverter with square end up into the cut section of the down pipe. Release any clips supporting the down pipe in order to insert the rain diverter body and refit once diverter is in place. Connect hose between rain rain diverter body and the water but connector. FINAL NOTE If correctly fitted, the butt will fill to within 10mm of the top. If water butt overflows - raise the butt. If water level is too low - lower the butt. If the water level is too low ensure rain has fallen to fill the butt before lowering. KIT INCLUDES: 1 x Rain Diverter 1 x 20mm Connector 1 x Washer 1 x Nut 1 x 500mm Hose

Suitable for use with all soluble chemicals, Adjustable width allows for spot weeding right up to lawn feeding, Cover widths from 10cm (4") up to 50cm (20"), Comes complete with an adapter to fit all watering cans with spouts up to 3cm in Diameter,

A gravity fed watering system offering the benefits of drip watering at a low price. 1. Take the plastic tube and connect to the plastic flow control device. 2. Take an empty water bottle, fill it with water and screw the flow control spike on to the top of the bottle. It will fit most plastic bottles up to 2Ltr. 3. Insert the flow control spike in to the soil so that the water bottle is upside down. 4. Turning the knob on the flow control spike will adjust the flow of the water. You will notice that air bubbles will form on the inside of the plastic bottle. This indicates that water is flowing out of the device. When the number of air bubbles becomes less, it means that the water flow is less. The minimum flow you should see is 1 bubble every 2 1/2 seconds.

Pack contains 2, Ideal for use with runner beans, peas or sweet pea plants, Holds 6 bamboo canes, Simply push in, no tying required, Made from durable plastic, will last for years,

Pack contains 30 x Small & 20 x Large, Easy to use plant clips, No tying required, Simply squeeze the clips together to open and place the clip around the plant stem and your cane to hold your plants in place,

A split ring for putting round the cane and plant stem to give support as the plant grows. No tying required, Pack Contains 25 Plastic Coated Plant Rings.

A split ring for putting round the cane and plant stem to give support as the plant grows. No tying required, Pack Contains 25 Galvanised Plant Rings.

Simply squeeze open with thumb and finger and put around the plant stem. Clip on to the cane to give support as the plant grows. No tying required, Pack Contains 5 Small Spring Plant Clips.

Pack contains 10, Simply place the caps on top of your garden canes and protect your eyes while working and bending in the garden, The tapered holes ensure a strong grip, Fits up to a ½" cane,

Pack contains 8 balls, Make up fruit cages and netting frames to protect your crops, This simple to use ball will take canes or metal tubing up to ½" in diameter, The tapered holes ensure a strong grip, Make any size frame required,

Test your soil before you grow. Pack contains test tube, measuring spoon, pipette, pH liquid, pH powder and detailed instruction book. Enough to perform 25 tests.

Test your soil before you grow. Pack contains 2 single use pH tests.

Simple to use, no battery required. Instant dry, moist or wet reading. Please note: without soil the meter will not return a reading.

Simple to use, no battery required. Instant acid or alkaline reading.

This thermometer can be mounted on a wall or post, Keep away from direct sources of heat, such as direct sunlight, which could give a false reading, Highest and lowest temperatures are recorded by marker indices which are set by the movement of the columns, The markers will record the highest and lowest temperatures since the last reset To reset: keep the red button depressed while the markers fall back to the columns.

This thermometer will help you determine the most comfortable and economical temperature in your home, This is usually between 16 - 24°C (61 - 75°F), Also suitable for outdoor use, Keep out of direct sunlight.

This thermometer will help you determine the most comfortable and economical temperature in your home, This is usually between 16 - 24°C (61 - 75°F), Also suitable for outdoor use, Keep out of direct sunlight.

This thermometer will help you determine the most comfortable and economical temperature in your home, This is usually between 16 - 24°C (61 - 75°F),

This thermometer will help you determine the most comfortable and economical temperature in your home, This is usually between 16 - 24°C (61 - 75°F), Also suitable for outdoor use, Keep out of direct sunlight.

Made from heavy duty galvanised steel. Suitable for use as a 3 arm or 4 arm chain. Simply remove one arm as required. 46cm (18") overall length.

Made from heavy duty galvanised steel. Ideal for many application around the home and garden. Perfect for hanging up and organising tools. Great for use in the shed or garage.

Made from heavy duty galvanised steel. Ideal for many application around the home and garden. Perfect for hanging up and organising tools. Great for use in the shed or garage.